Yazoo/Kees ZKWQL48190 Manuale dell'Operatore

Operator’s ManualModels: Z12APlease read these instructions carefully and makesure you understand them before using the machine.Z12 CommercialCollecti

10Engine Mount and Vacuum AssemblyTools Required:1. 9/16" wrench2. Ratchet3. 9/16" socket.4. 7/16" socket5. 3/8” wrench6. Flat Sc

11Spindle Drive & Drive KitAssembly1. Remove the discharge chute.2. Remove the right hand belt shield.3. Remove the deck belt from the right spind

12Hose AttachmentInletHoseClampHoseClampBootHoseClampLowerHoseNOTE:Hoses may need to be trimmed to fit. Ifnecessary, see the Hose Trimmingsection at

13RodEndArmDoorClevis PinDoor Tightness AdjustmentHose TrimmingTools Required: Utility Knife1. Carefully measure the length needed. Re-member that a

14Servicing the Engine1. Make sure that engine oil is at enginemanufacturer’s recommended level (refer toengine manual).2. Fill the fuel tank. Us

15Preventative Maintenance Schedule Item Before Every Every

16Engine Service and MaintenanceFollow the engine manufacturer’s maintenanceinstructions. Should any malfunction occur withthe engine during the warr

17 PROBLEM POSSIBLE CAUSE CORRECTION Engine Does Not Start. 1. Spark plug wire disconnecte

18NOTE: Your Front Weight Bar, Boot, and Hitch may look different from those shown in this diagram.AUXILIARY ENGINE ASSEMBLY

19NOTE: Your Front Weight Bar and Hitch may look different from those shown in this diagram.SPINDLE DRIVE ASSEMBLY

2Operators GuideSpecifications ... 3Features and Controls (Au

20CONTAINER ASSEMBLY1234567891011121314151617181920212223244111218812181225262728

21ITEM PART NO. QTY DESCRIPTION1 ... 108969 ... 1 ...CONTAINER ASM.2 ... 200839 ... 1 ...

22FRAME ASSEMBLY1234567891011121314151617181920212223241176

23FRAME ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... 061651 ... 1 ...THROTTLE CABLE2 ... 062072 ...

24POWER UNIT ASSEMBLY12345678910111213141516171819202122235644

25POWER UNIT ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... 092705 ... 1 ... INLET, BLOWER HSG.2 ... 094005 ..

26HITCH ASSEMBLYQuantity 3 for Spindle Drive UnitsQuantity 4 for Auxiliary Engine Units1234567891011121314151413141410141410

27HITCH ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... 099693 ... 2 ...PIN, WIRE LOCK2 ... 200749 ...

28SPINDLE DRIVE ASSEMBLY123456789101112131415161718192021222324252627282930313233343536373940414243444523272128282927158292814384646

29SPINDLE DRIVE ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... (539) 106752 ... 1... FAN COVER W/DECALS2 ... (539) 1089

3 Length 38 in. (97 cm.) Width (without engine mount or vacuum assembly)

30DRIVE KIT ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... (539) 108950 ... 1... 42 SHIELD... (539) 108953 ... 1...

31

32Technical Assistance:For technical assistance, please contact your local dealeror Yazoo/Kees Customer Service.Yazoo/Kees Power Equipment700 Park St.

4FEATURES & CONTROLSAuxiliary EngineNOTE: Your Front Weight Bar, Boot, and Hitch may look different from those shown in this diagram.ContainerRel

5Spindle DriveNOTE: Your Front Weight Bar and Hitch may look different from those shown in this diagram.FEATURES & CONTROLSContainerReleaseLeverI

6SAFETY RULESSafety Procedures1 - Training:• Read the Operator’s manual. If the operator(s)or mechanic(s) can not read English it is theowner’s respo

7SAFETY RULES3 - Operation• Never run an engine in an enclosed area.• Only operate in good light, keeping away fromholes and hidden hazards.• Slow dow

8Unpacking InstructionsAssembly InstructionsFrame Assembly UpperFrameLowerFrameTools Required:1. 3/4"

9Mounting the Z12NOTE: This portion of the assembly requires lifting the Z12; two people are required.Tools Required: 1. 9/16" wrench 2